ALPHA MOTO

Motorcycle Carburetor Synchronization gauge

Essential tool for your regular motorcycle maintenance!

  • Made in Taiwan with superior quality! 

  • Each gauge has its own individual damping control and calibration control

  • Comes with both 5mm and 6mm brass adapters, works virtually all make of motorcycles

Fast shipping

Same day shipping, order placed by 11am PST will be shipped same day, then expect to receive your order within 2-3 days!

Huge savings

No sales tax for residence outside Nevada! 8%-9% savings

30 days money back guarantee

If you are not completely satisfied with your order, just send it back within 30 days!

carburetor synchronizer

Carburetor Synchronizer

This vacuum gauge set features 2 precision gauges.Gauge reading: 0-38hg

Each gauge has its own individual damping control and Calibration Control. Gauges are mounted to a heavy metal base intended for bench top use.It can be modified for 4 or 6 cylinder use.

pls check out below video for demonstration. (the item in the video is 4 cylinder gauge, this listing is for 2 cylinder gauge)  

Parts included in the Kit:

1 qty x Bracket
2 qty x 2 & 3/4" Gauges
2 qty x Hoses 4mm(.I.D)x7mm(O.D.)x75cm (L)
2 qty x plastic Valves 5.5mm(O.D.)
1 qty x 180mm(M5xP0.8) Brass Extension
1 qty x 65mm(M5xP0.8) Brass Extension



STOCK IS LIMITED, BUY IT NOW BEFORE IT IS GONE

0

  • Essential tool for regular motorcycle maintenance !

  • Every DIY motorcyclist should have one in their garages!

  • Good inexpensive solution to improve your bike's performance!

five-star reviews

How to calibrate the gauge:

Before each use, make sure all the gauges are calibrated to 0.

If the needle on the gauge is not pointed at 0:

open the plastic cap, and use a flat head screwdriver to rotate the screw (circle in red in the picture) on the gauge face to adjust the pointer to 0 or the position desired.

HOW IT WORKS

Please refer to above video for tuning process (demo shows 4 gauges, you will get a 2 Gauge set!

Set up procedure

1. Position the gauge properly.


2. Set up the gauge as per picture indicated (picture shows 4 gauges, buyer will get two gauge set in this listing).

cut the rubber hoses in two pieces, and connect the hoses with white plastic valves, attach the rubber hoses with the gauge.


3.Remove the vacuum attachment plug-screws from the carburetor flanges or intake manifolds and install the brass adapters in these holes ( long adapters to inside carbs and short adapters to the outside carbs).


*Run the engine until operating temperature is reached, carburetors must be adjusted with engine warm and the choke fully open

Tuning Procedure

1. Start the engine, let it idle and check the gauges.

2. If the needles are bounced all over the place, adjust the valves slightly, the needles will flutter, but should not oscillate more than one graduation on the gauge faces.

3. If one gauge is out of sync, adjust the adjusting screw between carbs until the sync is obtained.

4. Shut off the bike, give the throttle a few snap-backs,let the bike settles in the new setup, and repeat the process until desired result is achieved.

QUESTIONS? LOOK HERE!

Can't find question? call or Text us +702-3362588 or email us alphamotoparts@gmail.com

Can i use this to tune my carbs on my mercury outboard boat motor?

Yes, so long as the carbs have threaded vacuum ports that match the threads on the gauge tubes. There are several different thread sizes (5mm or 6mm) available for various carbs and throttle bodies

Does it have in line (or in hose) adjuster to cut down on needle fluctuation?

Yes, it does. It comes with 4 plastic in-line adjusters,  you will need to cut a section of each hose and attach the plastic valve with each end of hoses (see setup procedure).

Will this unit work with a Johnson or Evinrude carbureted 2 cyl, 3 cyl, 4 cyl and v6 outboard motor?

For V6, you can sync 2 carbs first, then sync another set of 3 or 4, or you can buy the four cylinder gauge (check below combo section), so you can sync all 6 carb gauge together. 

Is this the only tool you will need to synchro a carb? Or are there other separate tools required?

You will  an auxiliary gas tank (check below combo section) and a long Philips screwdriver to access the adjustment screws. 

Are the dial faces made of glass or plastic?

It is made of plastic.

Will this work 1989 yamaha fzr 1000 with mikuni carbs

Yes, it is universal application, it comes with 6mm adapter, which will fit for your bike.

How about fuel injection throttle bodies?

Sorry, no.

HUGE SAVINGS ON COMBOS!

Choose your package and save big on your order

carb sync tool

BEST DEAL

$126.95$104.95

Now Only

$104.95

100% No-Risk Money Back Guarantee

ALPHA MOTO Universal Motorcycle Vacuum Carburetor Synchronizer Synchronization Carb Sync 4 Cylinder Gauge - ALPHA MOTO

BEST DEAL

$88.95$72.98

Now Only

$72.98

100% No-Risk Money Back Guarantee

Your 100% satisfaction is our goal!

No matter if you are a professional mechanic or amateur - ALPHA MOTO is your reliable partner when it comes to motorcycle tools and parts.